Author Topic: WANTED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft  (Read 3237 times)

0 Members and 1 Guest are viewing this topic.

VeeSix

  • Hero Member
  • *****
  • Posts: 648
WANTED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« on: December 04, 2010, 04:57:09 PM »
Does anyone have a Alfa Romeo Guilietta 2.0 propellar shaft available???
GTV shaft is a bit shorter than Guilietta so will not fit, but i am also thinking a Alfetta shaft would be the same
If anyone has one available please let me know price and location
« Last Edit: December 19, 2010, 03:06:31 PM by VeeSix »
1985 Alfa Romeo GTV6 V6 2.5 12V 
1986 Alfa Romeo 90 V6 2.5 12V
1990 Alfa Romeo 75 V6 3.0 12V Potenziata
1990 Alfa Romeo 164 V6 3.0 12V Zender
1991 Alfa Romeo 164 V6 3.0 12V QV
1992 Alfa Romeo 164 V6 3.0 12V QV

75TS

  • Full Member
  • ***
  • Posts: 144
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #1 on: December 04, 2010, 07:40:13 PM »
I have one from an 85 guiletta & will check on condition on tuesday...

prova

  • Full Member
  • ***
  • Posts: 186
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #2 on: December 04, 2010, 08:25:52 PM »
Mate I have one from an 82 Alfetta GTV. I think it is in okay condition - you can have it for free but the freight cost might be the problem. I am located near Geelong, Vic.

Ren

MD

  • Hero Member
  • *****
  • Posts: 1752
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #3 on: December 04, 2010, 10:23:19 PM »
A coupe shaft is shorter than the sedan.

This goes for the majority of models because the sedans are longer in the wheelbase.

The Alfetta should fit the  Giulietta both of them being sedans.

It takes considerable amount of work to remove and install a transaxle driveshaft. Be sure the replacment shaft has good locating bearings, seals, centre bearing, rubber couplings and is correctly balanced otherwise there will be some hair tearing down the track...guaranteed.

While you at it, it will pay to check the front and rear transaxle rubber mounts, clutch slave cylinder leaks, rear caliper leaks and diff output shaft leaks.
Transaxle Alfas Haul More Arse.

hammer

  • Hero Member
  • *****
  • Posts: 688
  • AROCA Member #: 510
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #4 on: December 04, 2010, 11:02:26 PM »
Hi there,

I have one from an 84 Alfetta sedan that I'll sell cheaply to you. PM me if you are keen. I can also look into freight.

Cheers,

Brent

VeeSix

  • Hero Member
  • *****
  • Posts: 648
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #5 on: December 04, 2010, 11:29:32 PM »
Personal messaged all responses thankyou
Thankyou MD for your notes, i always take regard of what someone saids, there is always something to learn
I have removed/restored/replaced propellar shafts about 20 times in my lifetime so am just used to it i guess, i do not even think about it anymore, just do it, basically just remove the exhaust, heat shield then propellar shaft bolts but yes i guess it is one of those jobs where as you do not want to be doing it everyday, it is alot better replacing all the parts but sometimes you just have to make do with what you got
1985 Alfa Romeo GTV6 V6 2.5 12V 
1986 Alfa Romeo 90 V6 2.5 12V
1990 Alfa Romeo 75 V6 3.0 12V Potenziata
1990 Alfa Romeo 164 V6 3.0 12V Zender
1991 Alfa Romeo 164 V6 3.0 12V QV
1992 Alfa Romeo 164 V6 3.0 12V QV

VeeSix

  • Hero Member
  • *****
  • Posts: 648
Re: WNATED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #6 on: December 19, 2010, 03:04:58 PM »
Still after a propellar shaft, would like to pick up this week if in NSW, if you have one available please send me your contact phone number and i will give you a ring as soon as possible.
1985 Alfa Romeo GTV6 V6 2.5 12V 
1986 Alfa Romeo 90 V6 2.5 12V
1990 Alfa Romeo 75 V6 3.0 12V Potenziata
1990 Alfa Romeo 164 V6 3.0 12V Zender
1991 Alfa Romeo 164 V6 3.0 12V QV
1992 Alfa Romeo 164 V6 3.0 12V QV

david sammartino

  • Full Member
  • ***
  • Posts: 188
Re: WANTED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #7 on: December 19, 2010, 07:37:10 PM »
i have one from my 84 giulietta 2.0, but im in melbourne.

Rigi

  • Full Member
  • ***
  • Posts: 155
  • AROCA Member #: 7933
Re: WANTED WANTED WANTED Alfa Romeo Guilietta 2.0 propellar shaft
« Reply #8 on: December 22, 2010, 08:07:15 AM »
Probably have a couple that are complete for you to choose from - please send PM with your details
Current
2010 GT 3.2 100 year Anniversary
1977 Alfetta GTV - Grp s
1974 GTV105 Resto (wip)
1977 Alfetta GTV Normal Roadie on Historics

Past
1980 Alfetta sedan('prettyboy')
1986 Alfetta GTV6GP
1985 Alfetta GTV6
1984 Alfetta GTV
1980 Alfetta Sedan
1978 Alfetta Sed